Connection Module Cat. 6A, 1xRJ45/u, Snap-in, grey, 100x

R509503

100 pcs

The module for the highest standards. Guarantees the best performance reserves for 10G Ethernet cabling and beyond.

The R&Mfreenet Cat. 6A unshielded connection modules, part of the Advanced cabling system, are ideal for voice, fast data transmissions and high bandwidth applications. This high-performance Cat. 6A module is perfect for use in 10 Gigabit Ethernet (10GBASE-T) and future high-speed applications to 500 MHz.

Scope of Supply

RJ45 Cat. 6A ISO connection module, unshielded

Snap-in adapter

Dust cover

Cable tie

Installation instructions

Technical Data

DESCRIPTION VALUE/VALUE RANGE
Standard / norm

UL Listed

IEC 60603-7-41: Electrical Characteristics of the Telecommunication Outlets

ISO/IEC 11801

EN 50173-1

Protection class IP

IP 20

IP 10 (correlates to NEMA 1)

PoE Yes
Connector class

connection module

Shielding connector (A)

unshielded

Connector type (A)

RJ45

Category connector (A)

Cat. 6A ISO

Holder for connector / module

Snap-in

Wiring diagram

T568A and T568B

Poles 8

Mechanical Data

DESCRIPTION VALUE/VALUE RANGE
Color

module, red / Snap-in adapter, gray (NCS 2502-B)

More performance

  • Innovation in twisted-pair connection technology

  • Reliable high-frequency data transmission

  • High performance enables 2 m short links and «25G Ready» support

  • Guaranteed 4dB margin NEXT on permanent link or channel

  • High density in the patch panel and rack

  • Assembly saves time and cost

More security

  • Innovatively protected signal transmission

  • Consistent performance

  • 360° shield housing

  • Large-area color coding

  • 100% quality control

  • «25G Ready»

More convenience

  • Quick and simple installation

  • Reliable IDC technology

  • Automatic cutting of wires

  • Each module delivered with protective cover

  • 90° and 180° orientation in one module

  • Exceeds the Cat. 6A ISO specification (mated) for the entire re-embedded plug range as specified by IEC 60603-7-51 (shielded), 60603-7-41 (unshielded) and IEC 60512-27-100. Exceeds the Cat. 6A specification (mated) for the entire re-embedded plug range as specified by TIA/EIA 568.2-D

  • Achieves exceptional margins when installed as part of an R&M Cat. 6A ISO 4-connector channel or permanent link, exceeding the IEEE 802.3™ Section Four minimum requirements for 10GBASE-T performance, as well as the requirements for Class EA performance according to ISO/IEC 11801 and Cat. 6A performance according to TIA/EIA 568.2-D

  • Meets the requirements of ISO/IEC TR11801-9905 together with Cat.7A installation cables with AWG22 and allows for 25GBase-T transmission up to 30m.

  • Automatic cutting of wires for precise, consistent termination

  • X-Separator isolates pairs from each other, minimizing influence of cable termination on NEXT performance

  • Use of all four sides of modules maximizes distance between pairs for optimum performance

  • GHMT and 3P certifications for Cat. 6A ISO component performance

RJ45 connection module of Cat. 6A ISO, for the setting up of transmission channels of Class EA with up to 4 plugged connections acc. to ISO/IEC 11801, EN 50173-1, (DIN EN 50173-1) and Class F on 2 pairs, complies with Cat. 6A requirements of the standards ISO/IEC 11801, EN 50173-1 as well the U.S. standard Cat. 6A according to TIA/EIA 568.2-D, re-embedded tested in acc. with IEC 60603-7-41 and 60512-27-100, interoperable and backwards compatible with Category 6 and Category 5e.

Suitable for 10GBASE-T applications in acc. with IEEE 802.3™ Section Four up to 500 MHz and 100 m.

Tested in line with R&M's manufacturing control, performing 100% inspection.

Compatible with RJ standard plugs (RJ11, RJ12, RJ45), connection with automatic wire cutting of installation cables AWG 26 – 22 (0.4 mm – 0.65 mm) and flexible cables AWG 26/7 – AWG 22/7 without special tools. X-Separator for individual pair shielding. Parallel pair termination without crossover in acc. with TIA 568-A/B, gold-plated bronze contacts for >1000 mating cycles, IDC contacts with >20 insertion cycles, contact resistance <5 mOhm, dielectric strength >1000 Veff. Supports PoE (IEEE 802.3af), PoEP (IEEE 802.3at), 4PpoE (IEEE 802.3bt) and is compatible to IEC 60512-99-001/002. 90° wire orientation without bending cable. With integral cable strain relief, including dust cover.

Material: halogen-free and heavy-metal free in acc. with EU directives RoHS 2.

Connection module Cat. 6A ISO, unshielded, with dust cover, snap-in frame (gray), cable tie and installation instructions.

Creating documents