Connection Module Cat. 6A, 1xRJ45/u, Snap-in, grey, 100x

R509503

100 pcs

The module for the highest standards, guarantees the best performance in the 10 Gigabit Ethernet cabling.

The R&Mfreenet Cat. 6A unshielded connection modules, part of the Advanced cabling system, are ideal for voice, fast data transmissions and high bandwidth applications. This high-performance Cat. 6A module is perfect for use in 10 Gigabit Ethernet (10GBASE-T) and future high-speed applications to 500 MHz.

Scope of Supply

RJ45 Cat. 6A ISO connection module, unshielded

Snap-in adapter

Dust cover

Cable tie

Installation instructions

Technical Data

DESCRIPTION [UNIT] VALUE/VALUE RANGE
Standard

UL Listed

IEC 60603-7-41: Electrical Characteristics of the Telecommunication Outlets

ISO/IEC 11801-1 Ed 1.0 2017-11

EN 50173-1: May 2011

Protection class IP

IP 20

PoE Yes
Connector class

connection module

Shielding connector (A)

unshielded

Connector type (A)

RJ45

Category connector (A)

Cat. 6A ISO

Holder for connector / module

Snap-in

Wiring diagram

TIA-568A / TIA-568B

Poles 8

Mechanical Data

DESCRIPTION [UNIT] VALUE/VALUE RANGE
Color

module, red / Snap-in adapter, gray (NCS 2502-B)

More performance

  • Innovation in twisted-pair connection technology

  • Reliable high-frequency data transmission

  • High performance enables 2 m short links

  • Guaranteed 4dB margin NEXT on permanent link or channel

  • High density in the patch panel and rack

  • Assembly saves time and cost

More security

  • Innovatively protected signal transmission

  • Consistent performance

  • 360° shield housing

  • Large-area color coding

  • 100% quality control

More convenience

  • Quick and simple installation

  • Reliable IDC technology

  • Automatic cutting of wires

  • Each module delivered with protective cover

  • 90° and 180° orientation in one module

  • Exceeds the Cat. 6A ISO specification (mated) for the entire re-embedded plug range as specified by IEC 60603-7-51 (shielded), 60603-7-41 (unshielded) and IEC 60512-27-100. Exceeds the Cat. 6A specification (mated) for the entire re-embedded plug range as specified by TIA 568-C.2

  • Achieves exceptional margins when installed as part of an R&M Cat. 6A ISO 4-connector channel or permanent link, exceeding the IEEE 802.3™ Section Four minimum requirements for 10GBASE-T performance, as well as the requirements for Class EA performance according to ISO/IEC 11801 ed. 2.2, 2011, and Cat. 6A performance according to TIA 568-C.2

  • Automatic cutting of wires for precise, consistent termination

  • X-Separator isolates pairs from each other, minimizing influence of cable termination on NEXT performance

  • Use of all four sides of modules maximizes distance between pairs for optimum performance

  • GHMT and 3P certifications for Cat. 6A ISO component performance

RJ45 connection module of Cat. 6A ISO, for the setting up of transmission channels of Class EA with up to 4 plugged connections acc. to ISO/IEC 11801 ed. 2.2, June 2011, EN 50173-1 May 2011 (DIN EN 50173-1) and Class F on 2 pairs, complies with Cat. 6A requirements of the standards ISO/IEC 11801 ed. 2.2, June 2011, EN 50173-1 May 2011, as well the U.S. standard Cat. 6A according to TIA 568-C.2, re-embedded tested in acc. with IEC 60603-7-41 and 60512-27-100, interoperable and backwards compatible with Category 6 and Category 5e.

Suitable for 10GBASE-T applications in acc. with IEEE 802.3™ Section Four up to 500 MHz and 100 m.

Tested in line with R&M's manufacturing control, performing 100% inspection.

Compatible with RJ standard plugs (RJ11, RJ12, RJ45), connection with automatic wire cutting of installation cables AWG 26 – 22 (0.4 mm – 0.65 mm) and flexible cables AWG 26/7 – AWG 22/7 without special tools. X-Separator for individual pair shielding. Parallel pair termination without crossover in acc. with TIA 568-A/B, gold-plated bronze contacts for >1000 mating cycles, IDC contacts with >20 insertion cycles, contact resistance <5 mOhm, dielectric strength >1000 Veff. Supports PoE (IEEE 802.3af), PoEP (IEEE 802.3at), 4PpoE (IEEE 802.3bt) and is compatible to IEC 60512-99-001/002. 90° wire orientation without bending cable. With integral cable strain relief, including dust cover.

Material: halogen-free and heavy-metal free in acc. with EU directives RoHS 2.

Connection module Cat. 6A ISO, unshielded, with dust cover, snap-in frame (gray), cable tie and installation instructions.

Creating documents