- Switzerland - English
- Contact
FTTH Precon solutions for overhead line development
Continuous fiber-optic connections to the end customer are one of the prerequisites for modern broadband data transmission to the home.
Since, up to now, a fiber-optic based FTTH development outside cities and conurbations has often not been worthwhile for telecom operators due to the high investments involved, there are still many undersupplied areas in rural areas even in highly technologized industrialized countries, including in Europe.
Aerial deployments are an interesting alternative to the classic, buried fiber optic network. Overground cabling has been around ever since we had electricity and telephone networks.
And FTTH can also be rolled out around two and a half times faster by means of overhead cabling and by using existing telephone or electricity company masts than with conventional
underground cabling.
Aerial deployments are an interesting alternative to the classic, buried fiber optic network. Overground cabling has been around ever since we had electricity and telephone networks. And FTTH can also be rolled out around two and a half times faster by means of overhead cabling and by using existing telephone or electricity company masts than with conventional underground cabling.
Robust, self-supporting and either single- or double-sided pre-assembled connection cables (ADSS and Drop) including IP- protected optical connectors and adapters, as well as innovative distribution boxes (RIO, SRS) and modern distribution closures (SYNO, ZOONA) for mast mounting, each optimized for the different levels of the network, form important solution components for the overhead expansion of fiber optic lines.
They are complemented by a wide-ranging portfolio of cable terminals (CONNEXIO) and boxes (POLARIS) to realize the last meters to the connection of the end customer property, again with partially or fully pre- assembled drop cables and correspondingly robust IP-protected connector as well as patch or splice technology.
With its new FTTH aerial portfolio, R&M provides a variety of system elements that set standards in terms of modularity, ease of use and flexibility.
Due to the pre-assembled cables adapted to the respective network topology, the pre-installed splitter configurations in the boxes or closures, the possibility of time separation between installation of the distribution infrastructure and connection of the end customer, the installation times are reduced and the efficiency in the project is increased.
All boxes, closures and terminals in the R&M Aerial Solutions portfolio are designed for climatically demanding environments and offer extremely robust and flexible solutions for a wide range of applications outside urban infrastructures worldwide.
With the SYNO closure and its innovative gel-sealing technology or the ZOONA closure with its modern, user-friendly QIKseal cable entries, R&M offers two alternative solutions for the distribution point (mast, street cabinet or shaft, PoP) as a transition between splice technology and Precon technology.
A1 – SYNO Closure(IP68)
ZOONA Closure (IP68)
The ZOONA Precon is a mechanically sealed closure for network applications in the access area. It is especially ideal for aerial deployments with its compact dimensions optimized for mast mounting plus it features IP-protected adapters and several application variants with integrated splitters and cables pre-assembled with connectors on both sides.
B1 – ZOONA Precon (IP68)
The CTO RIO Box is designed as a flexible, multifunctional box in the aerial access area and can be installed on a mast. The internal structure of the box can be individually configured and conveniently equipped and maintained outside the already installed housing.
B2 – CTO RIO Box (IP65)
The SRS Box is available as a fully pre-assembled box for rapid network expansion in two configurations. It is optimized for the use of pre-assembled cables. It offers simple network migration and expandability as well as low-cost and project-specific adaptation through different splitter variants.
B3 – SRS Box (IP65)
C1 – Fiber Optic ADSS Cable
C2 – Fiber Optic Drop Cable
The Polaris-box family was designed as a multifunctional, versatile and individually equipable box for the termination of fiber optic connections in FTTx networks. It meets the requirements of protection class IP65 (NEMA4). For outdoor cabling applications, 100% precon or combined precon/splice or precon/patch variants are available.
D1 – Polaris-box 4 / 6
The TAP box is a certified compact box for one incoming and up to 6 outgoing fiber connections/cables.
D2 – TAP-box (IP67)
Cable used for industrial environments with high temperatures and chemical resistance.
Made for field applications. The FM45 is suitable for every need indoors and outdoors.
In- and Outdoor AP outlets made of impact-resistant complies with protection classes IP54 and IP67, also it is UV and weather resistant.
IP54 / IP66 enclosure suitable for the installation of modules for category 6A s/u.
Suitable for RJ45 connection modules “special” and fiberoptic connectors with adapter frame.
The enclosure, which achieves protection class IP67, can be assembled and commissioned directly on site.
Cable used for industrial environments with high temperatures and chemical resistance.
In- and Outdoor AP outlets made of impact-resistant complies with protection classes IP54 and IP67, also it is UV and weather resistant.
Protection class IP54 for dust and UV resistant.
R&Mindustry Patch Cord Cat. 6A, equipped with PUR jackets, ideal for use in harsh environments.
The enclosure, which achieves protection class IP67, can be assembled and commissioned directly on site.
CONEXIO flexx supports all FTTA/PTTA/HTTA applications in the field of outdoor cabling on masts, on radio towers or roofs of skyscrapers.
Where space is tight, there is still room for the CONEXIO lite. It is the divider solution of choice when antenna masts are to accommodate a high number of radio heads. It is particularly suitable in difficult weight and space conditions. When network operators upgrade or share a 4G site, this compact, lightweight, wind-stable divider often fits.
The CONEXIO easy makes FTTA/PTTA/HTTA installations faster, safer and overall simpler.
The Cable Head Terminal is available in fiber optic, copper, and hybrid versions for up to 12 radio heads.
Plug & Play also applies to the connection between CONEXIO solutions and the remote radio heads. R&M has developed the CONEXIO jump family with fiber and power connectivity for this purpose.
19” panel for fiber management in the base stations, allows flexible cable and patch cord routing with space for 24 LC-Duplex adapters.
For classical installation of single radioheads, CONEXIO discrete connects RRH’s with the BBU unit.
CONEXIO flexx supports all FTTA/PTTA/HTTA applications in the field of outdoor cabling on masts, on radio towers or roofs of skyscrapers.
Where space is tight, there is still room for the CONEXIO lite. It is the divider solution of choice when antenna masts are to accommodate a high number of radio heads. It is particularly suitable in difficult weight and space conditions. When network operators upgrade or share a 4G site, this compact, lightweight, wind-stable divider often fits.
The CONEXIO easy makes FTTA/PTTA/HTTA installations faster, safer and overall simpler.
The Cable Head Terminal is available in fiber optic, copper, and hybrid versions for up to 12 radio heads.
Plug & Play also applies to the connection between CONEXIO solutions and the remote radio heads. R&M has developed the CONEXIO jump family with fiber and power connectivity for this purpose.
The CONEXIO portfolio includes all accessories for antenna cabling, be it FTTA, PTTA or HTTA.
It has been optimized for combination with all CONEXIO solutions.
For classical installation of single radioheads, CONEXIO discrete connects RRH’s with the BBU unit.
CONEXIO flexx supports all FTTA/PTTA/HTTA applications in the field of outdoor cabling on masts, on radio towers or roofs of skyscrapers.
Where space is tight, there is still room for the CONEXIO lite. It is the divider solution of choice when antenna masts are to accommodate a high number of radio heads. It is particularly suitable in difficult weight and space conditions. When network operators upgrade or share a 4G site, this compact, lightweight, wind-stable divider often fits.
The CONEXIO easy makes FTTA/PTTA/HTTA installations faster, safer and overall simpler.
The Cable Head Terminal is available in fiber optic, copper, and hybrid versions for up to 12 radio heads.
Plug & Play also applies to the connection between CONEXIO solutions and the remote radio heads. R&M has developed the CONEXIO jump family with fiber and power connectivity for this purpose.
19” panel for fiber management in the base stations, allows flexible cable and patch cord routing with space for 24 LC-Duplex adapters.
For classical installation of single radioheads, CONEXIO discrete connects RRH’s with the BBU unit.
CONEXIO flexx supports all FTTA/PTTA/HTTA applications in the field of outdoor cabling on masts, on radio towers or roofs of skyscrapers.
Where space is tight, there is still room for the CONEXIO lite. It is the divider solution of choice when antenna masts are to accommodate a high number of radio heads. It is particularly suitable in difficult weight and space conditions. When network operators upgrade or share a 4G site, this compact, lightweight, wind-stable divider often fits.
The CONEXIO easy makes FTTA/PTTA/HTTA installations faster, safer and overall simpler.
The Cable Head Terminal is available in fiber optic, copper, and hybrid versions for up to 12 radio heads.
Plug & Play also applies to the connection between CONEXIO solutions and the remote radio heads. R&M has developed the CONEXIO jump family with fiber and power connectivity for this purpose.
19” panel for fiber management in the base stations, allows flexible cable and patch cord routing with space for 24 LC-Duplex adapters.
For classical installation of single radioheads, CONEXIO discrete connects RRH’s with the BBU unit.
Our range of fiber optic cables for aerial installation consists of self-supporting All Dielectric Self Support (ADSS) types designed for mast installation. The cables are available in various designs as central loose tube (CLT) or stranded loose tube (SLT) cables and are designed for different spans up to 200m pole distances.
Designed for fiber-to-the-subscriber applications, our drop cable is designed for short spans of up to 60 m, but can be easily installed on facades and, thanks to its “Cca” CPR classification, in buildings. It has a round shape and is a fully dielectric cable ideal for termination in wall boxes or enclosures.
The Polaris-box family was designed as a multifunctional, versatile and individually equipable box for the termination of fiber optic connections in FTTx networks.
The TAP box is a certified compact box for one incoming and up to 6 outgoing fiber connections/cables.
With the SYNO closure and its innovative gel-sealing technology or the ZOONA closure with its modern, user-friendly QIKseal cable entries, R&M offers two alternative solutions for the distribution point (mast, street cabinet or shaft, PoP) as a transition between splice technology and Precon technology.
The ZOONA Precon closure for network applications in the access area. It is especially ideal for aerial deployments with its compact dimensions optimized for mast mounting plus it features IP-protected adapters and several application variants with integrated splitters and cables pre-assembled with connectors on both sides.
Loose-tube cables can contain either one single tube with colored optical fibers, either multiple tubes. We use either FRLSZH (Fire-Retardant, Low-Smoke, Zero-Halogen) jacketing compounds for indoor or universal (indoor/ outdoor) installation either PE (Polyethylene) compounds for outdoor installation as well as other special compounds.
Two families with strong siblings and convincing design: The Polaris-box family with five boxes and the Venus family with four boxes complete average sized DCIs. There are various flexible possibilities for equipping the connection boxes.
The SYNO dome closure fulfills all requirements of a modern FO network with the innovative gel technology. The SYNO closure is particularly characterized by its unique modularity and flexibility.
Rodent-protected, non-metallic stranded loose tube cable with up to 432 fibers in a 18-strand stranding, for outdoor duct installation. Individual loose tubes are equipped with 24 fibers.
Data center infrastructure, airports, public buildings, co-locations, or in-house high-security infrastructure at banks and insurances or in the chemical and pharmaceutical industry – Netscale Family covers the whole spectrum. The most flexible mixed media patch panel with the best cable management system combines everything and offers everything on a single height unit in the rack.
R&M inteliPhy net is your easy-to-use DCIM solution for asset, capacity and change management. Reduce implementation time and ensures high data quality of your documentation with great IT infrastructure visualizations.
With its BladeShelter line, R&M is able to offer a perfect solution for conditioning all datacenter solutions that maintain cold or warm air through closed structures and energy distribution systems with environmental control of the datacenter.
Raceway systems pick up the fiber optics at the building entry point and direct them reliably into the distributor halls and operative zones. In the process, the raceway installation guarantees important all-round protection for the sensitive fiber optic cables.
With its BladeShelter line, R&M is able to offer a perfect solution for conditioning all datacenter solutions that maintain cold or warm air through closed structures and energy distribution systems with environmental control of the datacenter.
Data center infrastructure, airports, public buildings, co-locations, or in-house high-security infrastructure at banks and insurances or in the chemical and pharmaceutical industry – Netscale Family covers the whole spectrum. The most flexible mixed media patch panel with the best cable management system combines everything and offers everything on a single height unit in the rack.
R&M inteliPhy net is your easy-to-use DCIM solution for asset, capacity and change management. Reduce implementation time and ensures high data quality of your documentation with great IT infrastructure visualizations.
The LC-QR connector has a push-pull mechanism integrated into the housing. It can be operated via the rear and the user no longer must grasp right to the front of the connector. Furthermore, the LC-QR can be locked and unlocked via the boot, and connectors and adapters can be packed more closely.
Raceway systems pick up the fiber optics at the building entry point and direct them reliably into the distributor halls and operative zones. In the process, the raceway installation guarantees important all-round protection for the sensitive fiber optic cables.
With an Optical Distribution Frame (ODF) network operators can now use their fiber distribution hub units in more varied ways.
The new PRIME ODF is a highly dense cabling platform. Its modules are suitable for the flexible use of fiber optic terminations.
The SCM ODF is coupled with SpliceMODULE, PatchMODULE or CombiMODULE and the Single Circuit Management System (SCM) for an application-independent solution.
Loose-tube cables can contain either one single tube with colored optical fibers, either multiple tubes. We use either FRLSZH (Fire-Retardant, Low-Smoke, Zero-Halogen) jacketing compounds for indoor or universal (indoor/ outdoor) installation either PE (Polyethylene) compounds for outdoor installation as well as other special compounds.
The LC-QR connector has a push-pull mechanism integrated into the housing. It can be operated via the rear and the user no longer must grasp right to the front of the connector. Furthermore, the LC-QR can be locked and unlocked via the boot, and connectors and adapters can be packed more closely.
Raceway systems pick up the fiber optics at the building entry point and direct them reliably into the distributor halls and operative zones. In the process, the raceway installation guarantees important all-round protection for the sensitive fiber optic cables.
Data center infrastructure, airports, public buildings, co-locations, or in-house high-security infrastructure at banks and insurances or in the chemical and pharmaceutical industry – Netscale 48 covers the whole spectrum. The most flexible mixed media patch panel with the best cable management system combines everything and offers everything on a single height unit in the rack.
Rodent-protected, non-metallic stranded loose tube cable with up to 432 fibres in a 18-strand stranding, for outdoor duct installation. Individual loose tubes are equipped with 24 fibers.
With its BladeShelter line, R&M is able to offer a perfect solution for conditioning all datacenter solutions that maintain cold or warm air through closed structures and energy distribution systems with environmental control of the datacenter.
With the patch boxes for fiber optic networks for 19″ racks, a common basic model accommodates both breakout cabling and splice cabling. The version for splice cabling is called UniRack 2 and contains a removable splice tray plate.
PoE LED Luminair or LED light with PoE driver
Example 3rd party product
WLAN or Thread Access Point
Example 3rd party product
Building Management Server with Building Operation Software
Example 3rd party product
Electrical blinds with PoE driver
Example 3rd party product
Multifunctional PoE Sensor (Light, Temperature, Air Quality, Presence, etc.)
Example 3rd party product
Network switch without Poe
Example 3rd party product
Zone Switch with PoE
and R&M Digital Ceiling Cabling:
Tailored solution per Switch design
Cisco CDB-8
Micro-Panel for Cisco Rack
Generic (Switch independent)
Power / Data U-Box with tailored switch adaptations
Microsens
DIN Rail distribution
R&M Digital Ceiling Cabling:
PowerSafe Patchcords or Pre-installed Zone cabling
R&M Digital Ceiling Cabling:
PoE proof Installation cables
PoE LED Luminair or LED light with PoE driver
Example 3rd party product
WLAN or Thread Access Point
Example 3rd party product
Building Management Server with Building Operation Software
Example 3rd party product
Electrical blinds with PoE driver
Example 3rd party product
Multifunctional PoE sensor (light, temperature, air quality, presence etc.)
Example 3rd party product
PoE capable network switch
Example 3rd party product
R&M Digital Ceiling Cabling
Service Outlet (SO) or Service Consolidation Point (SCP)
Multiple options depending on size
X-Small:
MPTL with FM45 (no SO)
Small:
Individual DIN Rail Service Outlets (SO)
Medium:
Surface mount boxes (SO)
Large:
U-Box as mini-distributor (SCP)
R&M Digital Ceiling Cabling:
PowerSafe Patchcords or Pre-installed Zone cabling
R&M Digital Ceiling Cabling:
PoE proof Installation cables
PoE LED Luminair or LED light with PoE driver
Example 3rd party product
WLAN or Thread Access Point
Example 3rd party product
Building Management Server with Building Operation Software
Example 3rd party product
Electrical blinds with PoE driver
Example 3rd party product
Multifunctional PoE sensor (light, temperature, air quality, presence etc.)
Example 3rd party product
PoE capable network switch
Example 3rd party product
R&M Digital Ceiling Cabling
Service Outlet (SO) or Service Consolidation Point (SCP)
Multiple options depending on size
X-Small:
MPTL with FM45 (no SO)
Small:
Individual DIN Rail Service Outlets (SO)
Medium:
Surface mount boxes (SO)
Large:
U-Box as mini-distributor (SCP)
R&M Digital Ceiling Cabling:
PowerSafe Patchcords or Pre-installed Zone cabling
R&M Digital Ceiling Cabling:
PoE proof Installation cables
Gel-free loose tube cable constructions ease and speed up the installation simply because are mess free with no gel to clean off.
The most installation friendly 19″ Patch Panel for connecting fiber cables using splicing technology safes time and provides secure fiber storage.
19″ Patch Panel for connecting pre-terminated fiber trunks or harnesses making quick and easy installations possible.
Genuine alternative to splicing – R&M’s «FO Field» connectors enables to complete projects quickly without any special training.
Data center infrastructure, airports, public buildings, co-locations, or in-house high-security infrastructure at banks and insurances or in the chemical and pharmaceutical industry – Netscale 48 covers the whole spectrum. The most flexible mixed media patch panel with the best cable management system combines everything and offers everything on a single height unit in the rack.
The HD ELISO patch panel is the perfect partner with an integrated cable tie shelf, accommodating up to 48 modules. Reusable cable guides facilitate fast assembly. Labeling and security systems are supported.
The R&M ELISO panel with Cat. 6A ISO modules, Cat. 6A EL modules or FO adapters can be equipped with the RFID-sensor bar system of R&MinteliPhy. Any combination of copper and fiber optic ports is possible.
R&M Netscale 120 solutions combine unmatched fiber cable management with automated connectivity tracking and an innovative tray design to deliver the world’s highest port density for 10/40/100G Ethernet.
Like all Netscale inserts, the adapter cassettes can be equipped with the RFID-sensor bar system of R&MinteliPhy.
The Analyzer can be mounted in 19″ network cabinets. Features LCD display and Ethernet interface. Controls up to 42 sensor bars.
R&MinteliPhy Port Monitoring Cords extend cabling visibility to server, switch and storage ports. They deliver visibility end to end, automate network documentation, continuously monitor connectivity and supervise changes.
R&M inteliPhy net is your easy to use DCIM solution for asset, capacity and change management. Reduce deployment time and ensure high data quality of your documentation with great IT infrastructure visualization.
Netscale 48 & Sensorbar
Data center infrastructure, airports, public buildings, co-locations or in-house high-security infrastructure at banks and insurances or in the chemical and pharmaceutical industry – Netscale 48 covers the whole spectrum. The most flexible mixed media patch panel with the best cable management system combines everything and offers everything on a single height unit in the rack.
Space-saving is a hot topic. And high density is the mega-trend. Production space in data centers is at a premium. That’s why the more compact thecabling, the more profitable the data center. But do compact high-density systems offer sustainable performance? Can they be operated efficiently and reliably? Of course they can. Experience high density without compromises. The HD Panel from R&M sets new standards in 19” rack systems. It packs more than just 48 ports into a single unit – namely freedom and flexibility, time savings and a future-proof design, and convenience and reliability.
Data center infrastructure, airports, public buildings, co-locations, or in-house high-security infrastructure at banks and insurances or in the chemical and pharmaceutical industry – Netscale 48 covers the whole spectrum. The most flexible mixed media patch panel with the best cable management system combines everything and offers everything on a single height unit in the rack.
Raceway systems pick up the fiber optics at the building entry point and direct them reliably into the distributor halls and operative zones. In the process, the raceway installation guarantees important all-round protection for the sensitive fiber optic cables.
QR patch cords are uniboot LC duplex and MPO assemblies that meet the high-density space requirements of the MDA and EDA. The highly flexible, interconnect cables reduces cable congestion, improves patch cord management and routing and improve air circulation.
Shielded twisted pair (STP) patch cords, for reliable high data rate transmissions and increased electromagnetic interference (EMI) protection.
Unshielded twisted pair (UTP) patch cords, where cost efficiency and ease of installation are the primary concern.
SFP+ conversion cables aggregate four 10G SFP+ or 25G SFP28 transceiver modules with LC-Duplex ports in a 40G QSFP+ or 100G QSFP28 transceiver with an MPO port.
Netscale 72 provides a single platform with best-in-class density, Base-8 and Base-12 fiber solutions for building large spine and leaf data center networks. It offers RFID-based automated port documentation and visual guidance of work orders.
The Netscale Blade Cabling Manager (BCM) is specifically designed for high port density switches. It enables a reliable, flexible, and highly efficient cable infrastructure throughout the data center.
Netscale BCM assemblies are custom-designed. Pre-configured, staggered cabling that matches port distances, zeroing out of cabling slack using linecard-optimized harness cable assemblies, and removing the need for cable management at the side of the cabinet.
Data center infrastructure, airports, public buildings, co-locations or in-house high-security infrastructure at banks and insurances or in the chemical and pharmaceutical industry – Netscale 48 covers the whole spectrum. The most flexible mixed media patch panel with the best cable management system combines everything and offers everything on a single height unit in the rack.
Complete SPE channel with IEC 63171-1 interface. Compatible to all outlets and 19” panels with R&Mfreenet holding plate adaptation
Application specific switch in the zone to cover the last few meters in the building automation
PoE LED Luminair or LED light with PoE driver
Example 3rd party product
WLAN or Thread Access Point
Example 3rd party product
Building Management Server with Building Operation Software
Example 3rd party product
Electrical blinds with PoE driver
Example 3rd party product
Multifunctional PoE Sensor (Light, Temperature, Air Quality, Presence, etc.)
Example 3rd party product
Network switch without Poe
Example 3rd party product
Zone Switch with PoE
and R&M Digital Ceiling Cabling:
Tailored solution per Switch design
Cisco CDB-8
Micro-Panel for Cisco Rack
Generic (Switch independent)
Power / Data U-Box with tailored switch adaptations
Microsens
DIN Rail distribution
R&M Digital Ceiling Cabling:
PowerSafe Patchcords or Pre-installed Zone cabling
R&M Digital Ceiling Cabling:
PoE proof Installation cables
PoE LED Luminair or LED light with PoE driver
Example 3rd party product
WLAN or Thread Access Point
Example 3rd party product
Building Management Server with Building Operation Software
Example 3rd party product
Electrical blinds with PoE driver
Example 3rd party product
Multifunctional PoE Sensor (Light, Temperature, Air Quality, Presence, etc.)
Example 3rd party product
PoE capable network switch
Example 3rd party product
R&M Digital Ceiling Cabling Service Outlet (SO) or Service Consolitation Point (SCP)
Multiple options depending on size
X-Small:
MPTL with FM45 (no SO)
Small:
Individual DIN Rail Service Outlets
Medium:
Surface mount boxes
Large:
U-Box as multiport outlet
R&M Digital Ceiling Cabling:
PowerSafe Patchcords or Pre-installed Zone cabling
R&M Digital Ceiling Cabling:
PoE proof Installation cables
With an Optical Distribution Frame (ODF) network operators can now use their fiber distribution hub units in more varied ways.
The new PRIME ODF is a highly dense cabling platform. Its modules are suitable for the flexible use of fiber optic terminations.
The SCM ODF is coupled with SpliceMODULE, PatchMODULE or CombiMODULE and the Single Circuit Management System (SCM) for an application-independent solution.
With the patch boxes for fiber optic networks for 19″ racks, a common basic model accommodates both breakout cabling and splice cabling. FibereasyRack 2 is the name of the version for breakout cabling. It contains a loose tube tray. The version for splice cabling is called UniRack 2 and contains a removable splice tray plate.
ODF Splitter Inserts offering low insertion loss, high directivity and return loss in a wide range of wavelengths and split ratios, plus ODF CWDM Inserts with Snap-in functionality for easy mounting, 8 channels, different wavelengths, complemented by a wide range of pre-connected ODF Patch Inserts / Breakouts configurable with LC duplex, SC or E2000 connectivity.
Plug-and-play solution enables simple installation of multifiber cable connections indoors.
Raceway systems pick up the fiber optics at the building entry point and direct them reliably into the distributor halls and operative zones. In the process, the raceway installation guarantees important all-round protection for the sensitive fiber optic cables.
Out there in the field a new age is dawning. Next Generation Networks are spreading. Street cabinets are gaining a new significance as outposts for fiber optic distribution in urban and rural areas.
Two families with strong siblings and convincing design: The Polaris-box family with five boxes and the Venus family with four boxes complete every FTTH project in no time at all. There are various flexible possibilities for equipping the connection boxes, so they are suitable for all typical applications and topologies.
A network makes a range of different demands on a closure. Depending on which area of the network they are used in, specific characteristics are required, such as splice capacity, flexibility or speed of installation.
Two families with strong siblings and convincing design: The Polaris-box family with five boxes and the Venus family with four boxes complete every FTTH project in no time at all. There are various flexible possibilities for equipping the connection boxes, so they are suitable for all typical applications and topologies.
Pre-assembled fiber optic outlet ready for easy and splice-free installation. Equipped with LC adaptors, which have an integrated self-closing metal laser protection shutter and are already terminated and tested with LC/APC connectors to a FITH cable in grade C/1.
Genuine alternative to splicing – R&M’s «FO Field» connectors enables to complete projects quickly without any special training.
Fiber optic outlet provide adequate fiber management and protection in various styles.
With an Optical Distribution Frame (ODF) network operators can now use their fiber distribution hub units in more varied ways.
The new PRIME ODF is a highly dense cabling platform. Its modules are suitable for the flexible use of fiber optic terminations.
The SCM ODF is coupled with SpliceMODULE, PatchMODULE or CombiMODULE and the Single Circuit Management System (SCM) for an application-independent solution.
With the patch boxes for fiber optic networks for 19″ racks, a common basic model accommodates both breakout cabling and splice cabling. FibereasyRack 2 is the name of the version for breakout cabling. It contains a loose tube tray. The version for splice cabling is called UniRack 2 and contains a removable splice tray plate.
ODF Splitter Inserts offering low insertion loss, high directivity and return loss in a wide range of wavelengths and split ratios, plus ODF CWDM Inserts with Snap-in functionality for easy mounting, 8 channels, different wavelengths, complemented by a wide range of pre-connected ODF Patch Inserts / Breakouts configurable with LC duplex, SC or E2000 connectivity.
Plug-and-play solution enables simple installation of multifiber cable connections indoors.
Raceway systems pick up the fiber optics at the building entry point and direct them reliably into the distributor halls and operative zones. In the process, the raceway installation guarantees important all-round protection for the sensitive fiber optic cables.
Out there in the field a new age is dawning. Next Generation Networks are spreading. Street cabinets are gaining a new significance as outposts for fiber optic distribution in urban and rural areas.
Two families with strong siblings and convincing design: The Polaris-box family with five boxes and the Venus family with four boxes complete every FTTH project in no time at all. There are various flexible possibilities for equipping the connection boxes, so they are suitable for all typical applications and topologies.
A network makes a range of different demands on a closure. Depending on which area of the network they are used in, specific characteristics are required, such as splice capacity, flexibility or speed of installation.
Two families with strong siblings and convincing design: The Polaris-box family with five boxes and the Venus family with four boxes complete every FTTH project in no time at all. There are various flexible possibilities for equipping the connection boxes, so they are suitable for all typical applications and topologies.
Pre-assembled fiber optic outlet ready for easy and splice-free installation. Equipped with LC adaptors, which have an integrated self-closing metal laser protection shutter and are already terminated and tested with LC/APC connectors to a FITH cable in grade C/1.
The Wall cabinet ODF consists of aluminum profiles with integrated backplane, side walls, doors and cover with brush type plates. For quick, easy click-in mounting of ODF components.
Fiber optic outlet provide adequate fiber management and protection in various styles.
Two families with strong siblings and convincing design: The Polaris-box family with five boxes and the Venus family with four boxes complete every FTTH project in no time at all. There are various flexible possibilities for equipping the connection boxes, so they are suitable for all typical applications and topologies.
Pre-assembled fiber optic outlet ready for easy and splice-free installation. Equipped with LC adaptors, which have an integrated self-closing metal laser protection shutter and are already terminated and tested with LC/APC connectors to a FITH cable in grade C/1.
Genuine alternative to splicing – R&M’s «FO Field» connectors enables to complete projects quickly without any special training.
Fiber optic outlet provide adaquate fiber management and protection in various styles.
Out there in the field a new age is dawning. Next Generation Networks are spreading. Street cabinets are gaining a new significance as outposts for fiber optic distribution in urban and rural areas.
Two families with strong siblings and convincing design: The Polaris-box family with five boxes and the Venus family with four boxes complete every FTTH project in no time at all. There are various flexible possibilities for equipping the connection boxes, so they are suitable for all typical applications and topologies.
A network makes a range of different demands on a closure. Depending on which area of the network they are used in, specific characteristics are required, such as splice capacity, flexibility or speed of installation.
With an Optical Distribution Frame (ODF) network operators can now use their fiber distribution hub units in more varied ways.
The new PRIME ODF is a highly dense cabling platform. Its modules are suitable for the flexible use of fiber optic terminations.
The SCM ODF is coupled with SpliceMODULE, PatchMODULE or CombiMODULE and the Single Circuit Management System (SCM) for an application-independent solution.
With the patch boxes for fiber optic networks for 19″ racks, a common basic model accommodates both breakout cabling and splice cabling. FibereasyRack 2 is the name of the version for breakout cabling. It contains a loose tube tray. The version for splice cabling is called UniRack 2 and contains a removable splice tray plate.
ODF Splitter Inserts offering low insertion loss, high directivity and return loss in a wide range of wavelengths and split ratios, plus ODF CWDM Inserts with Snap-in functionality for easy mounting, 8 channels, different wavelengths, complemented by a wide range of pre-connected ODF Patch Inserts / Breakouts configurable with LC duplex, SC or E2000 connectivity.
Plug-and-play solution enables simple installation of multifiber cable connections indoors.
Raceway systems pick up the fiber optics at the building entry point and direct them reliably into the distributor halls and operative zones. In the process, the raceway installation guarantees important all-round protection for the sensitive fiber optic cables.
R&M Netscale 120 solutions combine unmatched fiber cable management with automated connectivity tracking and an innovative tray design to deliver the world’s highest port density for 10/40/100G Ethernet.
LC-duplex patch cord with LSZH jacket, F8 2.0×4.1 mm, bend-optimized fiber.
LC-QR patch cords are uniboot integrated reverse-polarity LC duplex assemblies that meet the high-density space requirements of the MDA and EDA. The highly flexible, interconnect cables reduces cable congestion, improves patch cord management and routing and improve air circulation.
The Netscale Blade Cabling Manager (BCM) is specifically designed for high port density switches. It enables a reliable, flexible, and highly efficient cable infrastructure throughout the data center.
Raceway systems pick up the fiber optics at the building entry point and direct them reliably into the distributor halls and operative zones. In the process, the raceway installation guarantees important all-round protection for the sensitive fiber optic cables.
The Netscale Blade Cabling Manager (BCM) is specifically designed for high port density switches. It enables a reliable, flexible, and highly efficient cable infrastructure throughout the data center.
Netscale assemblies are pre-terminated cables with one or more LC-QR, MPO8 or MPO12 connectors on both ends, purpose made for high density backbone connections between cabinets or zones in the data center. Netscale assemblies conform with TIA-568 C.0 Types A or B polarity. Fast traceability is guaranteed with color coded jackets (OM5 – lime green, OM4 – heather violet, OM3 – aqua, OS2 – yellow).
Two families with strong siblings and convincing design: The Polaris-box family with five boxes and the Venus family with four boxes complete every FTTH project in no time at all. There are various flexible possibilities for equipping the connection boxes, so they are suitable for all typical applications and topologies.
Pre-assembled fiber optic outlet ready for easy and splice-free installation. Equipped with LC adaptors, which have an integrated self-closing metal laser protection shutter and are already terminated and tested with LC/APC connectors to a FITH cable in grade C/1.
Genuine alternative to splicing – R&M’s «FO Field» connectors enables to complete projects quickly without any special training.
Multimedia outlet for combination coaxial and data line in different styles.
Out there in the field a new age is dawning. Next Generation Networks are spreading. Street cabinets are gaining a new significance as outposts for fiber optic distribution in urban and rural areas.
Two families with strong siblings and convincing design: The Polaris-box family with five boxes and the Venus family with four boxes complete every FTTH project in no time at all. There are various flexible possibilities for equipping the connection boxes, so they are suitable for all typical applications and topologies.
A network makes a range of different demands on a closure. Depending on which area of the network they are used in, specific characteristics are required, such as splice capacity, flexibility or speed of installation.
With an Optical Distribution Frame (ODF) network operators can now use their fiber distribution hub units in more varied ways.
The new PRIME ODF is a highly dense cabling platform. Its modules are suitable for the flexible use of fiber optic terminations.
The SCM ODF is coupled with SpliceMODULE, PatchMODULE or CombiMODULE and the Single Circuit Management System (SCM) for an application-independent solution.
With the patch boxes for fiber optic networks for 19″ racks, a common basic model accommodates both breakout cabling and splice cabling. FibereasyRack 2 is the name of the version for breakout cabling. It contains a loose tube tray. The version for splice cabling is called UniRack 2 and contains a removable splice tray plate.
ODF Splitter Inserts offering low insertion loss, high directivity and return loss in a wide range of wavelengths and split ratios, plus ODF CWDM Inserts with Snap-in functionality for easy mounting, 8 channels, different wavelengths, complemented by a wide range of pre-connected ODF Patch Inserts / Breakouts configurable with LC duplex, SC or E2000 connectivity.
Plug-and-play solution enables simple installation of multifiber cable connections indoors.
Raceway systems pick up the fiber optics at the building entry point and direct them reliably into the distributor halls and operative zones. In the process, the raceway installation guarantees important all-round protection for the sensitive fiber optic cables.
Integrated, passive network isolator for the galvanic isolation of electrical devices for overvoltage protection.
Protective housing for IP67 proof connectivity in frequently cleaned locations.
Extra slim installation data cable for applications with restricted cable routing.
Expand the functionality of existing cabling, by using one cable for multiple devices (cable sharing) with R&M splitter solutions.
POLAN floor distributor easy to install and its clearly presented quick assembly technology makes handling quite comfortable.
Mini-Breakout cables are robust, easy to install and an ideal solution for direct connector mounting. Alternatively FiTH cable as mini loose tube construction are the prefect fit when it comes to splicing application.
Fiber optic outlet provide adequate fiber management and protection in various styles.
Rugged Patch Cord ensures network availability in mechanically rough conditions such as offices or any other similar public areas..
Installation cables with high EMC protection against outside disturbances.
Field Mountable connection FM45 for links without TO (MPTL).
Automated infrastructure management system for complete control what is going on in the installation.
Coding accessories to improve cabling availability by reducing handling mistakes.
Outdoor installation cables with extra protection against the harsh and wet environment.
Made for field applications. The FM45 is suitable for every need indoors and outdoors.
Protection class IP67 for splash, weather and UV resistant.
In- and Outdoor AP outlets made of impact-resistant complies with protection class IP54 and IP67, also it is UV and weather resistant.
Buried and rodent protected FO cables.
The shielded R&MhealthLine Outlets reduce the risk of spreading bacterias and germs as a result of touching the patch cord.
The shielded R&MhealthLine Outlets reduce the risk of spreading bacteria and germs as a result of touching the patch cord.
Coding accessories to improve cabling availability by reducing handling mistakes.
Installation data cable for home applications with moderate data volume up to 1GBit/s.
Field Mountable connection FM45 for links without TO (MPTL).
Extra slim installation data cable for applications with restricted cable routing.
Indoor distributor with dedicated space for home wiring cabling and active network termination equipment.
Adapter for data connectivity for integration into DIN rail based distributors.
Extra short, low diameter patch cords for easy handling within inhouse distributors.
Inexpensive, low density 19″ panel for home applications.
Terminal outlets for data connections in different styles.
Multimedia outlet for combination coaxial and data line in different styles.
Coaxial installation cable for distribution of CATV, radio and satellite broadcast.
Indoor / Outdoor cables meet the combined requirements of the two environments.
Field Mountable connection FM45 for links without TO (MPTL).
Outlets for exposed positions on remote locations with improved IP protection.
Multipair cables provide a huge number of pairs in a compact cable volume.
Distribution panels with IDC punch down blocks (110 style) for high density termination of individual pairs.
Modular distribution panels use a subset of pins of the popular RJ45 interface for plug and play connection.
POLAN floor distributor easy to install and its clearly presented quick assembly technology makes handling quite comfortable.
Splitter insert module featuring despite easy plug n’ play installation a safe network operation.
Mini-Breakout cables are robust, easy to install and an ideal solution for direct connector mounting. Alternatively FiTH cable as mini loose tube construction are the prefect fit when it comes to splicing application.
Genuine alternative to splicing – R&M’s «FO Field» connectors enables to complete projects quickly without any special training.
Fiber optic outlet provide adequate fiber management and protection in various styles.
Rugged Patch Cord ensures network availability in mechanically rough conditions such as offices or any other similar public areas.
High performance twisted pair cabling for reliable 10G / 25G / 40G data rate transmissions.
Service Outlet
Scalable and modular distribution boxes with protection against mechanical stress.
FM45
Field Mountable connection FM45 for links without TO (MPTL).
Unshielded twisted pair (UTP) connectivity, where cost efficiency and ease of installation are the primary concern.
Unshielded twisted pair (UTP) installation cables, where cost efficiency and ease of installation are the primary concern.
Unshielded twisted pair (UTP) patch cords, where cost efficiency and ease of installation are the primary concern.
Stable 19″ panels with easy handling, color code capabilities and sophisticated labeling concept.
Terminal outlets of different styles with easy handling, color code capabilities and sophisticated labeling concept.
Tailor-made designed robust consolidation point distributors in scalable sizes.
The SYNO dome closure fulfills all requirements of a modern FO network with the innovative gel technology. The SYNO closure is particularly characterized by its unique modularity and flexibility.
Two families with strong siblings and convincing design: The Polaris-box family with five boxes and the Venus family with four boxes complete average sized DCIs. There are various flexible possibilities for equipping the connection boxes.
Loose-tube cables can contain either one single tube with colored optical fibers, either multiple tubes. We use either FRLSZH (Fire-Retardant, Low-Smoke, Zero-Halogen) jacketing compounds for indoor or universal (indoor/ outdoor) installation either PE (Polyethylene) compounds for outdoor installation as well as other special compounds.
Rodent-protected, non-metallic stranded loose tube cable with up to 432 fibers in a 18-strand stranding, for outdoor duct installation. Individual loose tubes are equipped with 24 fibers.
With an Optical Distribution Frame (ODF) network operators can now use their fiber distribution hub units in more varied ways.
The new PRIME ODF is a highly dense cabling platform. Its modules are suitable for the flexible use of fiber optic terminations.
The SCM ODF is coupled with SpliceMODULE, PatchMODULE or CombiMODULE and the Single Circuit Management System (SCM) for an application-independent solution.
Raceway systems pick up the fiber optics at the building entry point and direct them reliably into the distributor halls and operative zones. In the process, the raceway installation guarantees important all-round protection for the sensitive fiber optic cables.
With an Optical Distribution Frame (ODF) network operators can now use their fiber distribution hub units in more varied ways.
The new PRIME ODF is a highly dense cabling platform. Its modules are suitable for the flexible use of fiber optic terminations.
The SCM ODF is coupled with SpliceMODULE, PatchMODULE or CombiMODULE and the Single Circuit Management System (SCM) for an application-independent solution.
The LC-QR connector has a push-pull mechanism integrated into the housing. It can be operated via the rear and the user no longer must grasp right to the front of the connector. Furthermore, the LC-QR can be locked and unlocked via the boot, and connectors and adapters can be packed more closely.
Loose-tube cables can contain either one single tube with coloured optical fibres, either multiple tubes. We use either FRLSZH (Fire-Retardant, Low-Smoke, Zero-Halogen) jacketing compounds for indoor or universal (indoor/ outdoor) installation either PE (Polyethylene) compounds for outdoor installation as well as other special compounds.
With the patch boxes for fiber optic networks for 19″ racks, a common basic model accommodates both breakout cabling and splice cabling. The version for splice cabling is called UniRack 2 and contains a removable splice tray plate.
The SYNO dome closure fulfills all requirements of a modern FO network with the innovative gel technology. The SYNO closure is particularly characterized by its unique modularity and flexibility.
Rodent-protected, non-metallic stranded loose tube cable with up to 432 fibres in a 18-strand stranding, for outdoor duct installation. Individual loose tubes are equipped with 24 fibers.
The LC-QR connector has a push-pull mechanism integrated into the housing. It can be operated via the rear and the user no longer must grasp right to the front of the connector. Furthermore, the LC-QR can be locked and unlocked via the boot, and connectors and adapters can be packed more closely.
Raceway systems pick up the fiber optics at the building entry point and direct them reliably into the distributor halls and operative zones. In the process, the raceway installation guarantees important all-round protection for the sensitive fiber optic cables.
Shielded twisted pair (STP) connectivity, for reliable high data rate transmissions and increased electromagnetic interference (EMI) protection.
Shielded twisted pair (STP) installation cables, for reliable high data rate transmissions and increased electromagnetic interference (EMI) protection.
Shielded twisted pair (STP) patch cords, for reliable high data rate transmissions and increased electromagnetic interference (EMI) protection.
Stable 19″ panels with easy handling, color code capabilities, sophisticated labeling concept and automatic earthing / ground bonding.
Terminal outlets of different styles with easy handling, color code capabilities and sophisticated labeling concept.
Tailor-made designed robust consolidation point distributors in scalable sizes.
Expand the functionality of existing cabling, by using one cable for multiple devices (cable sharing) with R&M splitter solutions.
Hit the button below and fill out the form. Our expert will contact you shortly.
